Published October 30, 2022 | Version v1
Journal article Open

Determining the influence of a filler on the properties of composite materials based on Phenylone C2 for tribojunctions in machines and assemblies

Creators

  • 1. Dnipro State Agrarian and Economic University

Description

The introduction of polymer-composite materials makes it possible not only to solve the problem of increasing durability, reducing the mass and cost of machines, but also, by introducing fillers, to adapt them to the required operating conditions. At the same time, there is a problem regarding the high cost of technologies for obtaining composites, which limits their widespread implementation. That is why the object of this research is the processes of influence of the filler on the characteristics and properties of polymer-composite materials.

Complex laboratory studies of physical and mechanical characteristics, tribological and thermophysical properties of the developed polymer-composite materials based on Phenylone C2 were carried out. The dependence of the coefficient of friction and wear of the material based on Phenylone C2, containing thermally expanded graphite, on the pressure and nature of counter-bodies during friction with lubrication and without it was established. It was revealed that the minimum amount of wear of the material, with friction with lubrication, is achieved under the pressure on tribojunction of 5 MPa. It was established that with an increase in the concentration of filler from 5 to 25 wt% the coefficient of thermal conductivity increases by 4–40.8 %, compared with that non-filled with Phenylone C2. It was found that the introduction of thermally expanded graphite into Phenylone C2 in the amount of 5 wt % leads to a decrease in heat capacity by 34 %. The proposed technology of obtaining polymer-composite materials in the electromagnetic field provides sufficient physical and mechanical characteristics, tribological properties and low cost of finished products (parts).

The results reported here make it possible to adapt the physical and mechanical characteristics, thermophysical and tribological properties of polymer-composite materials to certain modes of operation of movable junctions

Files

Determining the influence of a filler on the properties of composite materials based on Phenylone C2 for tribojunctions in machines and assemblies.pdf

Files (2.4 MB)

Additional details

References

  • Hsissou, R., Seghiri, R., Benzekri, Z., Hilali, M., Rafik, M., Elharfi, A. (2021). Polymer composite materials: A comprehensive review. Composite Structures, 262, 113640. doi: https://doi.org/10.1016/j.compstruct.2021.113640
  • Dykha, A., Svidersky, V., Danilenko, I., Bilichenko, V., Kukurudzyak, Y., Kirichenko, L. (2020). Design and study of nanomodified composite fluoropolymer materials for tribotechnical purposes. Eastern-European Journal of Enterprise Technologies, 5 (12 (107)), 38–48. doi: https://doi.org/10.15587/1729-4061.2020.214533
  • Derkach, O., Artemchuk, V., Muranov, Е. (2017). Regarding to issue of machinability processing the polymeric composites for seeding machines. Visnyk Kharkivskoho natsionalnoho tekhnichnoho universytetu silskoho hospodarstva imeni Petra Vasylenka, 181, 157–166. Available at: http://nbuv.gov.ua/UJRN/Vkhdtusg_2017_181_27
  • Aulin, V., Derkach, O., Makarenko, D., Hrynkiv, A., Pankov, A., Tykhyi, A. (2019). Analysis of tribological efficiency of movable junctions "polymeric­composite materials ‒ steel." Eastern-European Journal of Enterprise Technologies, 4 (12 (100)), 6–15. doi: https://doi.org/10.15587/1729-4061.2019.176845
  • Gilbert, M. (2017). Aliphatic Polyamides. Brydson's Plastics Materials, 487–511. doi: https://doi.org/10.1016/b978-0-323-35824-8.00018-9
  • Krasinskyi, V., Suberlyak, O., Sikora, J., Zemke, V. (2021). Nanocomposites based on polyamide-6 and montmorillonite intercalated with polyvinylpyrrolidone. Polymer-Plastics Technology and Materials, 60 (15), 1641–1655. doi: https://doi.org/10.1080/25740881.2021.1924201
  • Kabat, O., Sytar, V., Sukhyy, K. (2018). Antifrictional Polymer Composites Based on Aromatic Polyamide and Carbon Black. Chemistry & Chemical Technology, 12 (3), 326–330. doi: https://doi.org/10.23939/chcht12.03.326
  • Burya, A. I., Dudin, V. Yu., Burya, A.A., Kholodilov, O. V. (2002). Friction and wear of the aromatic polyamide filled with thermally disintegrated graphite. Trenie i Iznos, 23 (3), 296–299. Available at: https://www.researchgate.net/publication/292487459_Friction_and_wear_of_the_aromatic_polyamide_filled_with_thermally_disintegrated_graphite
  • Tomina, A.-M. V., Burya, O. I., Lytvynova, Ye. E., Gavrish, V. M. (2020). The research on the influence of titanium-tantalum-tungsten-cobalt hard alloy on the tribological properties of phenylone C-2. Problems of Tribology, 25 (2), 42–48. doi: https://doi.org/10.31891/2079-1372-2020-96-2-42-48
  • Ivanochkin, P. G., Dolgopolov, K. N., Danilchenko, S. A. (2018). Creation of Oil-Filled Composites of Tribotechnical Purpose Based on Aromatic Polyamide Phenylone C-2. Solid State Phenomena, 284, 14–19. doi: https://doi.org/10.4028/www.scientific.net/ssp.284.14
  • Ivanochkin, P. G., Danilchenko, S. A., Novikov, E. S. (2016). Antifriction Composites Based on Phenylone C2 for Work under Conditions of Dry Friction. Procedia Engineering, 150, 520–526. doi: https://doi.org/10.1016/j.proeng.2016.07.033
  • Dudin, V., Makarenko, D., Derkach, O., Muranov, Y. (2021). Determination of the influence of a filler on the properties of composite materials based on polytetrafluorothylene for tribosystems of mechanisms and machines. Eastern-European Journal of Enterprise Technologies, 4 (12 (112)), 61–70. doi: https://doi.org/10.15587/1729-4061.2021.238452