Published October 30, 2022 | Version v1
Journal article Open

Optimization of the composition of cast iron for cast parts operating under abrasive friction, according to the criterion of maximum wear resistance

Creators

  • 1. National Technical University «Kharkiv Polytechnic Institute»

Description

The object of research: Titanium-alloyed hypoeutectic iron for mixer blades operating under abrasive friction conditions. Investigated problem: selection of the optimal titanium content in the alloy according to the criterion of the maximum wear resistance coefficient. The main scientific results: the content of titanium in cast iron was determined, which provides the maximum wear resistance coefficient with various compositions of the base alloy. It has been established that with the same titanium content, the highest value of the wear resistance coefficient depends on the carbon content and the position of the eutectic point on the Fe-C state diagram. In the studied range, the highest values of the wear resistance coefficient correspond to the average range of variation of these factors. This allows to say that the effect of carbon content and the position of the eutectic point doubly affect wear resistance at the same titanium content, and there is a range of titanium content in which the effect of these factors on the wear resistance value becomes the same. The area of practical use of the results of the study: the results obtained can be used by designers of industrial enterprises choosing materials for the manufacture of machine parts subject to intense friction due to operating conditions. The wear caused by this friction leads to the failure of the blades, so the designer's task is to choose the one that maximizes the durability of the blades. Innovative technological product: wear-resistant hypoeutectic cast iron alloyed with titanium for cast parts operating in conditions of intense abrasive friction The scope of the technological innovative product: mixing plants of various types, mainly used in road construction, construction and agriculture.

Files

Optimization of the composition of cast iron for cast parts operating under abrasive friction, according to the criterion of maximum wear resistance_zenodo.pdf

Files (1.4 MB)

Additional details

References

  • Golub, G., Myhailovych, Y., Achkevych, O., Chuba, V. (2019). Optimization of angular velocity of drum mixers. Eastern-European Journal of Enterprise Technologies, 3 (7 (99)), 64–72. doi: https://doi.org/10.15587/1729-4061.2019.166944
  • Hassanpour, A., Tan, H., Bayly, A., Gopalkrishnan, P., Ng, B., Ghadiri, M. (2011). Analysis of particle motion in a paddle mixer using Discrete Element Method (DEM). Powder Technology, 206 (1-2), 189–194. doi: https://doi.org/10.1016/j.powtec.2010.07.025
  • Gao, W., Liu, L., Liao, Z., Chen, S., Zang, M., Tan, Y. (2019). Discrete element analysis of the particle mixing performance in a ribbon mixer with a double U-shaped vessel. Granular Matter, 21 (1). doi: https://doi.org/10.1007/s10035-018-0864-4
  • Li, S., Kajiwara, S., Sakai, M. (2021). Numerical investigation on the mixing mechanism in a cross-torus paddle mixer using the DEM-CFD method. Powder Technology, 377, 89–102. doi: https://doi.org/10.1016/j.powtec.2020.08.085
  • Bohl, D., Mehta, A., Santitissadeekorn, N., Bollt, E. (2011). Characterization of Mixing in a Simple Paddle Mixer Using Experimentally Derived Velocity Fields. Journal of Fluids Engineering, 133 (6). doi: https://doi.org/10.1115/1.4004086
  • Zaselskiy, V., Shved, S., Shepelenko, M., Suslo, N. (2020). Modeling the horizontal movement of bulk material in the system "conveyor – rotary mixer." E3S Web of Conferences, 166, 06008. doi: https://doi.org/10.1051/e3sconf/202016606008
  • Frolova, L., Barsuk, A., Nikolaiev, D. (2022). Revealing the significance of the influence of vanadium on the mechanical properties of cast iron for castings for machine-building purpose. Technology Audit and Production Reserves, 4 (1 (66)), 6–10. doi: https://doi.org/10.15587/2706-5448.2022.263428
  • Demin, D. A. (1998). Change in cast iron's chemical composition in inoculation with a Si-V-Mn master alloy. Litejnoe Proizvodstvo, 6, 35.
  • Kontorov, B. M., Kunin, N. M. (1960). Iznosostoykie belye chuguny, legirovany borom i titanom. Liteynoe proizvodstvo, 4.
  • Emelyushin, A. N. (2000). Vliyanie titana i bora na iznosostoykost' chuguna prednaznachennogo dlya mehanicheskoy obrabotki nemetallicheskih materialov instrumenta iz hromistyh chugunov. Izvestiya vysshih uchebnyh zavedeniy. Chernaya metallurgiya, 2, 28–29.
  • Mohanad, M. K., Kostyk, V., Domin, D., Kostyk, K. (2016). Modeling of the case depth and surface hardness of steel during ion nitriding. Eastern-European Journal of Enterprise Technologies, 2 (5 (80)), 45–49. doi: https://doi.org/10.15587/1729-4061.2016.65454
  • Kostik, K. O. (2015). Development of the high-speed boriding technology of alloy steel. Eastern-European Journal of Enterprise Technologies, 6 (11 (78)), 8–15. doi: https://doi.org/10.15587/1729-4061.2015.55015
  • Kharchenko, S., Barsuk, A., Karimova, N., Nanka, A., Pelypenko, Y., Shevtsov, V., Morozov, I., Morozov, V. (2021). Mathematical model of the mechanical properties of Ti-alloyed hypoeutectic cast iron for mixer blades. EUREKA: Physics and Engineering, 3, 99–110. doi: https://doi.org/10.21303/2461-4262.2021.001830
  • Vasenko, Iu. A. (2012). Technology for improved wear iron. Technology Audit and Production Reserves, 1 (1 (3)), 17–21. doi: https://doi.org/10.15587/2312-8372.2012.4870
  • Domin, D. (2013). Artificial orthogonalization in searching of optimal control of technological processes under uncertainty conditions. Eastern-European Journal of Enterprise Technologies, 5 (9 (65)), 45–53. doi: https://doi.org/10.15587/1729-4061.2013.18452
  • Demin, D. (2017). Strength analysis of lamellar graphite cast iron in the «carbon (C) – carbon equivalent (Ceq)» factor space in the range of C = (3,425-3,563) % and Ceq = (4,214-4,372) %. Technology Audit and Production Reserves, 1 (1 (33)), 24–32. doi: https://doi.org/10.15587/2312-8372.2017.93178