DEVELOPMENT OF A MODEL OF TOOL SURFACE DRESSING WHEN GRINDING WITH CROSSED WHEEL AND CYLINDRICAL PART AXES
Authors/Creators
- 1. Chernihiv National University of Technology
- 2. Genix Solutions LLC
- 3. PJSC «CHEZARA»
- 4. PET TECHNOLOGIES
Description
Three-dimensional geometric modeling of the forming process of cylindrical parts during grinding with crossed axes of it and the wheel has been carried out. Grinding of shafts, which are widely used in the automotive industry, machine tool industry, and rolls of strip rolling mills has been carried out at one location with a wide abrasive wheel oriented relative to the workpiece. Based on the obtained spatial model of shaping and removal of the allowance, the distribution of the allowance along the cutting area of the tool during grinding with an oriented tool has been studied. It has been shown that on the peripheral cutting section of the grinding wheel, roughing, finishing and calibration are combined.
A modular three-dimensional model of dressing the grinding wheel peripheral section with a single-chip diamond tool during grinding with crossed axes of the tool and part using standardized modules of the dressing tool, orientation and shaping has been developed. Based on the presented model, the geometric accuracy of the tool peripheral section shaping after its dressing has been studied. Based on the presented model, the geometric accuracy of the tool peripheral section shaping after its dressing has been studied. In order to obtain the necessary microgeometry and cutting properties of abrasive wheels, in accordance with the features of processing the rolls of strip rolling mills with an oriented tool, dressing with a reduced feed rate of the dressing tool to the calibration section is proposed. The feed rate of the dressing single-chip tool depends on the value of allowance. Different feed rates of the dressing tool provide different development of the tool cutting peripheral section. This, in turn, increases the intervals between dressing processes of the grinding wheel, which operates in the blunt mode. Therefore, the resistance is increased, and the cost of processing is reduced. Implementation of the proposed method of wheel dressing during single-pass grinding with crossed axes of the tool and cylindrical part will provide high accuracy, quality of the machined surfaces, and also significantly increase the efficiency and productivity of processing. The developed dressing method can be applied for round grinding processes with crossed axes of the workpiece and abrasive wheels
Files
Development of a model of tool surface dressing when grinding with crossed wheel and cylindrical part axes.pdf
Files
(845.0 kB)
| Name | Size | Download all |
|---|---|---|
|
md5:b7f0bd3dce12d5b132931302850bba8f
|
845.0 kB | Preview Download |
Additional details
References
- Shkarlet, S., Kholiavko, N., Dubyna, M., Zhuk, O. (2019). Innovation, Education, Research Components of the Evaluation of Information Economy Development (as Exemplified by Eastern Partnership Countries). Marketing and Management of Innovations, 70–83. doi: https://doi.org/10.21272/mmi.2019.1-06
- Nadolny, K., Słowiński, B. (2011). The Effects of Wear upon the Axial Profile of a Grinding Wheel in the Construction of Innovative Grinding Wheels for Internal Cylindrical Grinding. Advances in Tribology, 2011, 1–11. doi: https://doi.org/10.1155/2011/516202
- Kalchenko, V. I., Kalchenko, V. V., Yeroshenko, A. M., Sira, N. M. (2016). Investigation of the method for grinding of the rolls of rolling mills with crossed axes of the tool and workpiece. Visnyk Cherkaskoho derzhavnoho tekhnolohichnoho universytetu, 4, 80–87. Available at: http://visnyk.chdtu.edu.ua/images/tech/4_2016/14.pdf
- Li, C. H., Qi, L. Y., Zhao, H. Y. (2011). Application and Development of High-Efficiency Abrasive Finishing. Advanced Materials Research, 189-193, 3113–3116. doi: https://doi.org/10.4028/www.scientific.net/amr.189-193.3113
- Hou, Y., Li, C., Zhou, Y. (2010). Applications of High-Efficiency Abrasive Process with CBN Grinding Wheel. Engineering, 02 (03), 184–189. doi: https://doi.org/10.4236/eng.2010.23026
- Quickpoint. Flexible high-performance grinding machine (2015). Available at: https://www.junker-group.com/fileadmin/user_upload/Prospekte/JUNKER_QUICKPOINT_en.pdf
- Technical solutions for roll grinding (2019). Norton Saint-Gobain. Available at: https://www.nortonabrasives.com/sga-common/files/document/ROLL%20GRINDING%20BROCHURE_apr2019.pdf
- Permyakov, A. A., Zhizhev, A. A. (2011). Improving the rough grinding technology for mill rolls by restoration of the grinding wheel cutting capacity without dressing. Visnyk SevNTU. Seriya: Mashynopryladobuduvannia ta transport, 118, 113–118. Available at: http://lib.sevsu.ru:8080/xmlui/bitstream/handle/123456789/4928/118_19.pdf?sequence=1&isAllowed=y
- Shakhbazov, Y. O., Shyrokov, V. V., Shyrokov, O. V., Palamar, O. O. (2018). Grinding process technology support. Printing and Publishing, 1 (75), 75–81. doi: https://doi.org/10.32403/0554-4866-2018-1-75-75-81
- Li, H. N., Axinte, D. (2016). Textured grinding wheels: A review. International Journal of Machine Tools and Manufacture, 109, 8–35. doi: https://doi.org/10.1016/j.ijmachtools.2016.07.001
- Young, H.-T., Chen, D.-J. (2005). Online dressing of profile grinding wheels. The International Journal of Advanced Manufacturing Technology, 27 (9-10), 883–888. doi: https://doi.org/10.1007/s00170-004-2271-8
- Fan, K.-C., Lee, M.-Z., Mou, J.-I. (2002). On-Line Non-Contact System for Grinding Wheel Wear Measurement. International Journal of Advanced Manufacturing Technology, 19 (1), 14–22. doi: https://doi.org/10.1007/pl00003964
- Kundrák, J., Fedorovich, V., Markopoulos, A. P., Pyzhov, I., Kryukova, N. (2014). Improvements of the Dressing Process of Super Abrasive Diamond Grinding Wheels. Manufacturing Technology, 14 (4), 545–554. Available at: https://www.researchgate.net/publication/269129723
- Kalchenko, V., Kolohoida, A., Kuzhelnyi, Y., Morochko, V. (2018). Single pass finishing grinding with crossed axes tool and cylindrical part. Technical sciences and technologies, 4 (14), 9–17. doi: https://doi.org/10.25140/2411-5363-2018-4(14)-9-17