World Academy of Science, Engineering and Technology
Published February 22, 2008 | Version 1259
Journal article Open

Modeling Parametric Vibration of Multistage Gear Systems as a Tool for Design Optimization

Authors/Creators

Description

This work presents a numerical model developed to simulate the dynamics and vibrations of a multistage tractor gearbox. The effect of time varying mesh stiffness, time varying frictional torque on the gear teeth, lateral and torsional flexibility of the shafts and flexibility of the bearings were included in the model. The model was developed by using the Lagrangian method, and it was applied to study the effect of three design variables on the vibration and stress levels on the gears. The first design variable, module, had little effect on the vibration levels but a higher module resulted to higher bending stress levels. The second design variable, pressure angle, had little effect on the vibration levels, but had a strong effect on the stress levels on the pinion of a high reduction ratio gear pair. A pressure angle of 25o resulted to lower stress levels for a pinion with 14 teeth than a pressure angle of 20o. The third design variable, contact ratio, had a very strong effect on both the vibration levels and bending stress levels. Increasing the contact ratio to 2.0 reduced both the vibration levels and bending stress levels significantly. For the gear train design used in this study, a module of 2.5 and contact ratio of 2.0 for the various meshes was found to yield the best combination of low vibration levels and low bending stresses. The model can therefore be used as a tool for obtaining the optimum gear design parameters for a given multistage spur gear train.

Files

1259.pdf

Files (377.7 kB)

Name Size Download all
md5:cedb4fd9d325897a63332232f6c2a45e
377.7 kB Preview Download

Additional details

References

  • Tamminana, V. K., Kahraman, A. and Vijayakar, S., "A study of the Relationship Between the dynamic factor and the dynamic transsmission error of spur gear pairs," in ASME 2005 International Design Engineering Technical Conferences and Computers and Information in Engineering conference, September 24-28 2005.
  • M. Vaishya and R. Singh, "Strategies for Modeling Friction in Gear Dynamics," Journal of Mechanical Design, vol. 125, pp. 383-393, 2003.
  • J. H. Kuang and A. D. Lin, "The Effect of Tooth Wear on the Vibration Spectrum of a Spur Gear Pair," Journal of Vibrations and Acoustics, vol. 123, pp. 311-317, 2001.
  • M. Vaishya and R. Singh, "Analysis of Periodically Varying Gear Mesh Systems with Coulomb Friction Using Floquet Theory," Journal of Sound and Vibration, vol. 243(3), pp. 525-545, 2001.
  • R. G. Parker, S. M. Vijayakar and T. Imajo, "Non-linear Dynamic Response of a Spur Gear Pair: Modelling and Experimental Comparisons," Journal of Sound and Vibrations, vol. 237(3), pp. 435-455, 2000.
  • L. Gelman, V. Giurgiutiu and A. Bayoumi, "Statistical Analysis of the Dynamic Mean Excitation for a Spur Gear," Journal of Vibrations and Acoustics, vol. 127, pp. 204-207, 2005.
  • G. Bonori, A. O. Andrisano and F. Pellicano, "Stiffness Evaluation and Vibration in a Tractor Gear," ASME International Mechanical Engineering Congress and Exposition, 2004.
  • M. A. Faith and O. Milosav, "Gear Vibration in Supercritical Mesh- Frequency Range," Faculty of Mechanical Engineering (FME), Belgrade, vol. 32, pp. 87-94, 2004.
  • R. G. Timothy, "Computer- Aided Design Software for Torsional Analysis," Master-s thesis, Virginia Polytechnic Institute and State University, 1998. [10] J. Lin and R. G. Parker, "Sensitivity of Planetory Gear Natural Frequencies and Vibration Modes to Model Parameters," Journal of Sound and Vibration, vol. 228(1), pp. 109-128, 1999. [11] Shengxiang Jia, Ian Howard and Jiande Wang, "The Dynamic Modeling of Multiple Pairs of Spur Gears in Mesh, Including Friction and Geometric Errors," International Journal of Rotating Machinery, vol. 9, pp. 437-442, 2003. [12] T. L. Krantz and M. Rashidi, "Vibration Analysis of a Split Path Gearbox," Tech. Rep., Army Research Laboratory, NASA, 1995. [13] Jian Lin and R. G. Parker, "Mesh Stiffness Variation Instabilities in a Two stage Gear System," Transactions of ASME, Journal of Vibration and Acoustics, vol. 124, pp. 68-76, 2002. [14] F. K. Choy, Y. K. Tu and D. P. Townsend, "Vibration Signature Analysis of a Multistage Gear Transmission," Tech Rep., NASA Lewis Research Center, 1989. [15] H. J. Sutherland and D. P. Burwinkle, "The Spectral Content of the Torque Loads on a Turbine Gear Tooth," Wind Energy, ASME, vol. 16, pp. 91-97, 1995. [16] M. L. James, G. M. Smith and P. W. Whaley, Vibration of Mechanical and Structural systems. Harper Collins College Publishers, 2nd ed., 1994. [17] Hsiang-Hsi Lin, Computer - Aided Design and Analysis of Spur Gear Dynamics. PhD Thesis, University of Cincinnati, 1985. [18] K. L. Johnson, Contact Mechanics. Cambridge University Press, 1985. [19] H. Xu and A. Kahraman, "Prediction of Mechanical Efficiency of Parallel - Axis Gear Pairs," Transactions of ASME, vol. 129, pp. 58-68, 2007. [20] D. W. Dudley, GEAR HANDBOOK: The Design, Manufacture and Application of Gears. McGraw-Hill Publishing Company, Newyork, 1st ed., 1962.