Marles, Jaana
Yim, Jihong
Ylilammi, Markku
Korpelainen, Virpi
Haimi, Eero
Verkama, Emma
Utriainen, Mikko
Puurunen, Riikka
Ylivaara, Oili
2021-05-31
<p>Thickness profile data measured for aluminium oxide thin film grown by atomic layer deposition (ALD) using trimethylaluminium and water as reactants at 300 degrees Celsius on an all-silicon lateral high-aspect-ratio (LHAR) test structure of type PillarHall(TM) LHAR3 (layout v1b), nominal gap height 500 nm. Part of this data has been used in the publication "Saturation profile based conformality analysis for atomic layer deposition: aluminum oxide in lateral high-aspect-ratio channels"<a href="https://doi.org/10.1039/D0CP03358H"> https://doi.org/10.1039/D0CP03358H</a>, where this sample was number 8 (unique manufacturing code V0001, see Table S3 of the supplementary info, which also contains details of the layouts: <a href="http://www.rsc.org/suppdata/d0/cp/d0cp03358h/d0cp03358h1.pdf">http://www.rsc.org/suppdata/d0/cp/d0cp03358h/d0cp03358h1.pdf</a>). </p>
<p>Thickness profiles have been measured optically after removal of the top membrane by adhesive tape, by spectroscopic reflectometry in the visible wavelength range. In the optical thickness measurements, the refractive index is assumed constant (refractive index vs. wavelength this has been determined earlier for similar films also grown at 300 degrees Celsius) and thickness is allowed to vary. The optical model consists of smooth single-crystal silicon and ALD aluminium oxide films. Any silicon oxide below the ALD film is counted in the aluminium oxide thickness. Also roughness will impact the measurement result. For each measurement point, the location, the fitted thickness, and the goodness of fit is presented. For the 50x magnification, measurement spot diameter size is estimated as about 5-6 micrometers. The raw data have the centre of measurement as zero point of horizontal axis. The data needs to be shifted horizontally to have the zero point at the beginning of the LHAR cavity. Sometimes, the removal of the membrane has not worked in the beginning of the cavity (where the support pillars in the PillarHall LHAR3 design are more densely located) and the measurement has been made on a place that includes membrane remnants. In such cases, the fit of the optical model to the results has been poor and the data points should be rejected. </p>
Funding for PillarHall-3 LHAR prototype fabrication at VTT was provided by the Academy of Finland via the Finnish Centre of Excellence on Atomic Layer Deposition and via Tekes (currently: Business Finland) via the PillarHall TUTL project (1125/31/2016). The work at Aalto University was supported by Puurunen's starting grant and by the Academy of Finland (COOLCAT consortium, decision no. 329978 and ALDI consortium, decision no. 331082).
https://doi.org/10.5281/zenodo.3974438
oai:zenodo.org:3974438
eng
Zenodo
https://doi.org/10.26434/chemrxiv.12366623
https://doi.org/10.1039/D0CP03358H
https://zenodo.org/communities/ald-saturation-profile-open-data
https://doi.org/10.5281/zenodo.3974437
info:eu-repo/semantics/openAccess
Creative Commons Attribution 4.0 International
https://creativecommons.org/licenses/by/4.0/legalcode
atomic layer deposition
saturation profile
ALD saturation profile
trimethylaluminium
conformality
ALD
PillarHall(TM)
LHAR
ALD Al2O3 thickness profile in microscopic rectangular channel, TMA-water 300 degC 500 cycles, PillarHall(TM) LHAR3-1b, V0001
info:eu-repo/semantics/other